manualshive.com logo in svg

RadioMaster TX16S, User Manual, Page: 44 / 59

Share
Download
RadioMaster TX16S User Manual Download Page 44

44

Cstm

Call custom curve (CV1-CV32), custom curve is set in curve page CURVE

Modes

: Select the corresponding flight mode, and the output trimming value that

affects this entry can be set by the flight mode entry

Switch

: Select the switch to activate this item (Note: This setting is added to this

item to add multiple lines of different settings to switch, if there is only one line

setting, do not set the activation switch, otherwise the switch will cause this item

to be completely invalid).

Warning

: Set the alert tone

Multpx

: Superposition method, output after superimposing with the value of the

previous stroke amount

Add: Additive superposition, the current value is added to the value of the

previous line and output
Multiply: multiplication, the current value is multiplied by the value of the

previous line and output
Replace: direct replacement, the value of the previous line is directly replaced

by the value of this line

The combination of these operations allows the creation of complex

mathematical operations and is often considered one of the biggest benefits of using

OpenTX.

Delay Up/Dn

: The response of the output can be delayed as the input changes.

(In seconds).

Slow Up/Dn

: Regarding input changes, the response of the output can be slowed.

For example, slow speed can be used to slow down retraction driven by a normal

proportional servo. The output will cover the time in seconds from 100 to + 100%.

Summary of Contents for TX16S




























































Reviews:

No comments