manualshive.com logo in svg

RadioMaster TX16S, User Manual, Page: 25 / 59

Share
Download
RadioMaster TX16S User Manual Download Page 25

25

-GLOBA FUNCTIONS:

Global function page. This page can customize various

global functions. Global functions are similar to special functions in model parameters,

but global functions are shared by all model parameters, while functions in model

parameters are only used by the current model.

-TRAINER:

Trainer aka Coach function page. In this page, you can set the control

ratio of each channel from the student mode remote control in the coach mode, and

the intervention ratio of the remote control in the coach mode.

-HARDWARE:

Hardware setting page. In this page, you can calibrate the gimbal

and voltage, set the name of the gimbal, set the functions and names of switches and

knobs, and view the underlying parameters of the hardware.

-VERSION:

Version page. On this page, you can view the remote controller

hardware type, OpenTX firmware version, and the functional items included in the

current firmware.

4.2.1 TOOLS (Tool page) description

4.2.2 SD CARD (SD Card Page) Instructions

Summary of Contents for TX16S




























































Reviews:

No comments