Radio Shack TAD-268 Page 47 Owner'S Manual Download | Manualshive

Page: 47 / 52

background image

47

CARE AND MAINTENANCE

Your Radio Shack TAD-268 25-Channel 10-Memory Cordless Telephone Answering
System with Two-Way Paging and Intercom is an example of superior design and
craftsmanship. The following suggestions will help you care for your TAD so you can
enjoy it for years.

Keep the TAD dry. If it gets wet, wipe it dry immediately. Liquids might
contain minerals that can corrode the electronic circuits.

Handle the TAD gently and carefully. Dropping it can damage circuit
boards and cases and can cause the TAD to work improperly.

Use and store the TAD only in normal temperature environments.
Temperature extremes can shorten the life of electronic devices and
distort or melt plastic parts.

Keep the TAD away from dust and dirt, which can cause premature
wear of parts.

Wipe the TAD with a damp cloth occasionally to keep it looking new.
Do not use harsh chemicals, cleaning solvents, or strong detergents
to clean it.

Modifying or tampering with the TAD’s internal components can cause a malfunction
and might invalidate your TAD’s warranty and void your FCC authorization to oper-
ate it. If your TAD is not operating as it should, take it to your local Radio Shack
store for assistance. If the trouble is affecting the telephone lines, the phone compa-
ny can ask you to disconnect the TAD until you have resolved the problem.

43-738.fm Page 47 Friday, August 13, 1999 1:51 PM

«
...
45
46
47
48
49
...
»

Summary of Contents for TAD-268





















































Reviews:

No comments

Related manuals for TAD-268

Brand: Sangoma Pages: 3

Brand: XPLORA Pages: 2

Brand: Cable & Wireless Pages: 10

Brand: Karel Pages: 56

Brand: Karel Pages: 55

Brand: Yealink Pages: 8

Brand: Yealink Pages: 2

Brand: AT&T Pages: 33

Brand: Octopus Pages: 103

Brand: Uniden Pages: 47

Brand: ClearSounds Pages: 57

Brand: Milwaukee Pages: 9

Brand: Swissvoice Pages: 42

Brand: Yealink Pages: 26

Brand: VTech Pages: 8

Brand: Telstra Pages: 46

Brand: TEH Pages: 11

Brand: Geemarc Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands