manualshive.com logo in svg

Radio Shack TAD-268, Owner'S Manual, Page: 23 / 52

Share
Download
Radio Shack TAD-268 Owner'S Manual Download Page 23

23

Using the Base

Follow these steps to record the outgo-
ing announcement from the base.

1. If the TALK indicator is on, press

TALK

 on the handset to turn it off.

Then, if the ANSWER or ANN
ONLY indicator is on, press

ERASE/STOP 

on the base to turn it

off.

2. Open the cassette deck compart-

ment on top of the base, then
press and hold down 

ANNOUNCE

RECORD

 inside the compartment

for about 1 second. You hear
beeps while the TAD rewinds the
tape for the announcement
backup. When the tape fully
rewinds, you hear a 2-second
beep.

3. Speak your outgoing announce-

ment into the microphone on top
of the base in a strong voice, from
about 12 inches away from the
front of the TAD. The TAD records
the announcement into digital
memory and onto the tape at the
same time.

4. When you finish your outgoing

announcement, press 

ERASE/

STOP

 on the base. You hear

another 2-second beep.

If you do not press 

ERASE/STOP 

with-

in 21 seconds, the TAD automatically
stops.

After the TAD records the announce-
ment, it automatically plays back the
announcement from digital memory
over the base’s speaker.

43-738.fm  Page 23  Friday, August 13, 1999  1:51 PM

Summary of Contents for TAD-268





















































Reviews:

No comments