manualshive.com logo in svg

Radio Shack TAD-268, Owner'S Manual, Page: 15 / 52

Share
Download
Radio Shack TAD-268 Owner'S Manual Download Page 15

15

USING THE TELEPHONE

Be sure you have completed the pro-
cedures in “Installation”  on Page 8 and
“Telephone Preparation” on Page 13
before you begin using the telephone.

CONFIRMATION AND 
ERROR TONES

When you press a button, the phone
sounds a brief tone to indicate that it
accepted the command. If three error
tones sound, you pressed a button in
error, you are out of range, the battery
is low, or there is too much interfer-
ence. Move the handset closer to the
base and try again, or recharge the
battery.

MAKING/ANSWERING A 
CALL

The quick call function automatically
gives you a dial tone when you lift the
handset from the cradle. (To turn off
quick call, see “Turning Quick Call
Off”).

To make a call (with quick call on), sim-
ply pick up the handset from the cra-
dle, or, if the handset is not on the
cradle, press 

TALK

 on the handset until

the TALK indicator on the handset
lights. When you hear a dial tone, dial
the phone number.

To answer a call (with quick call on),
pick up the handset from the cradle, or,
if the handset is not on the cradle,
press 

TALK

 on the handset.

When you are finished with the call,
hang up by either pressing 

TALK 

so the

TALK indicator turns off, or return the
handset to the cradle.

Turning Quick Call Off

The quick call function is preset to 

on

at the factory, but you can turn it off.

Follow these steps if you want to can-
cel this function so the phone does not
give you a dial tone when you lift the
handset from the cradle.

1. If the TALK indicator on the hand-

set is on, press 

TALK

 to turn it off.

2. If the ANSWER or ANN ONLY

indicator on the base is on, press

ERASE/STOP 

to turn it off.

43-738.fm  Page 15  Friday, August 13, 1999  1:51 PM

Summary of Contents for TAD-268





















































Reviews:

No comments