Radio Shack TAD-268 Page 34 Owner'S Manual Download

Page: 34 / 52

Note: Each pause or tone entry
uses one digit of the TAD’s 32-
digit memory capacity.

5. Press

MEMORY

to store the num-

ber. A long beep sounds and the
HOLD/INT indicator turns off.

Notes:

• If you receive a call while storing a

number, press

TALK

to answer the

call. After the call, begin again at
Step 2 to store the number.

• To delete a number from memory,

repeat all steps except Step 4.

Turning the Auto Call
Function On/Off

Once you have stored a pager or tele-
phone number and have selected and
stored a remote operation security
code, you can follow these steps to
turn on the auto call function.

Notes:

• You cannot turn the auto call func-

tion on if you have new messages
you have not listened to.

• If you have not stored the code

and number, the AUTO CALL indi-
cator flashes rapidly

1. If the TALK indicator is on, press

TALK

on the handset to turn it off.

Then, if the ANSWER or ANN
ONLY indicator is on, press

ERASE/STOP

on the base to turn it

off.

2. Press ,

then

MEMORY

. The

HOLD/INT indicator blinks and a
beep sounds.

3. Press

4. Enter the number of call attempts

using the number buttons (1-9).

5. Press

MEMORY

to store the set-

ting. The HOLD/INT indicator
turns off and a long beep sounds.
The AUTO CALL indicator on the
base turns on.

6. Press the button next to the

ANSWER indicator on the base to
set the TAD to answer calls.

You can change the auto call setting
remotely. See “Remote Operation” on
Page 36.

To turn the auto call function off, follow
Steps 1-6, but enter

as the number in

Step 4.

43-738.fm Page 34 Friday, August 13, 1999 1:51 PM

Summary of Contents for TAD-268





















































Search results

Summary of Contents for TAD-268

Reviews:

Related manuals for TAD-268

Brands by name

Popular brands

Radio Shack TAD-268, Owner'S Manual

Search results

Summary of Contents for TAD-268

Reviews:

Related manuals for TAD-268

Brands by name

Popular brands