Radio Shack TAD-268 Page 31 Owner'S Manual Download | Manualshive

Page: 31 / 52

background image

31

ERASING MESSAGES

The TAD records new messages over
any old messages you do not want to
save. But, you can erase all stored
messages on a tape at one time. This
is convenient if you want to use tapes
you used in the TAD in other recording
devices, or to prevent others from play-
ing your messages again.

Note: You must use the controls on
the base to erase messages.

1. Play the incoming messages.

When the TAD has played back
the last message, press and
release

ERASE/STOP

.

2. While pressing and holding down

ERASE/STOP

, press

REWIND

. The

TAD rewinds the tape, then era-
ses all the messages (up to the
end of the new messages). After
the TAD finishes erasing the tape,
it rewinds the tape to the begin-
ning and stops.

Notes:

• The TAD will not answer calls

while it is erasing messages. If the
TAD is set to receive calls, press-
ing

ERASE/STOP

sets the TAD not

to answer calls.

• To stop erasing messages, press

ERASE/STOP

again.

• If you receive a call while erasing,

press

TALK

on the handset or lift

the handset from the cradle to

answer the call. After the call,
repeat Steps 1-2 to continue eras-
ing the messages.

RECORDING A MEMO

You can use the TAD to record a re-
minder for yourself or a message for
someone in your home or office. You
can record a memo using either the
base or the handset.

Note: When you record a memo, the
TAD saves the memo on the incoming
message tape like other recorded
messages.

Using the Base

Follow these steps to record a memo
at the base.

1. Press

MEMO

. The TAD beeps for

about 2 seconds, and the MEMO
indicator lights.

2. After the TAD stops beeping,

begin recording the message.
Speak in a strong voice from
about 12 inches away from the
front of the TAD.

43-738.fm Page 31 Friday, August 13, 1999 1:51 PM

«
...
29
30
31
32
33
...
»

Summary of Contents for TAD-268





















































Reviews:

No comments

Related manuals for TAD-268

Brand: Milwaukee Pages: 13

Brand: Uniden Pages: 48

Brand: Clarke Pages: 16

Brand: Sagem Pages: 64

Brand: Oricom Pages: 24

Brand: Daewoo Pages: 33

Brand: Kodak Pages: 25

Brand: Panacom Pages: 16

CT.TS005.002501.UK

Brand: Talkswitch Pages: 16

Brand: Swyx Pages: 3

Brand: BT Pages: 72

Brand: Doro Pages: 12

Brand: Doro Pages: 28

Brand: Doro Pages: 44

Brand: Doro Pages: 36

Brand: Doro Pages: 24

Brand: Doro Pages: 40

Brand: Avaya Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands