Radio Shack TAD-268 Page 18 Owner'S Manual Download

Page: 18 / 52

USING HOLD

To put a caller on hold, press

HOLD/IN-

TERCOM

on the handset so the TALK

indicator blinks and the HOLD/INT in-
dicator lights.

To return to the call, press

TALK

Notes:

• If you pick up another phone con-

nected to the same telephone line
while a call is on hold, the TAD-
268 automatically releases the
hold and you can talk with the
caller.

• After you put a call on hold, you

can use the handset to talk to a
person at the base using the inter-
com feature. See “Using the Inter-
com.”

• If you do not release a call on hold

within 5 minutes, the handset
beeps for 1 minute, then the
phone automatically hangs up.

USING THE INTERCOM

Use the intercom feature when you
want to talk with someone at the hand-
set or the base.

Follow these steps to call from the
handset to the base.

1. Press

HOLD/INTERCOM

on the

handset. The base rings three
times, then the base’s speaker
and microphone automatically
turn on. You can talk with some-
one at the base.

2. When you complete your conver-

sation, press

HOLD/INTERCOM

the handset again, or the person
at the base can press

INTERCOM

Follow these steps to call from the
base to the handset.

1. Press

INTERCOM

on the base.

The handset rings. (This is handy
for locating the handset when it is
away from the base.)

2. When the person at the handset

presses

HOLD/INTERCOM,

you

can talk with them.

3. When you complete the conversa-

tion, either press

INTERCOM

the base again, or the person at
the handset can press

HOLD/

INTERCOM

43-738.fm Page 18 Friday, August 13, 1999 1:51 PM

Summary of Contents for TAD-268





















































Search results

Summary of Contents for TAD-268

Reviews:

Related manuals for TAD-268

Brands by name

Popular brands

Radio Shack TAD-268, Owner'S Manual

Search results

Summary of Contents for TAD-268

Reviews:

Related manuals for TAD-268

Brands by name

Popular brands