manualshive.com logo in svg

Racktivity ES2000 Seriesl, User Manual, Page: 35 / 52

Share
Download
Racktivity ES2000 Seriesl User Manual Download Page 35

© 2011 Racktivity NV 

 

35/52

 

Antwerpsesteenweg 19 - 9080 Lochristi - Belgium  -  www.racktivity.com 

v 2014.3.27 

Note:

   The complete CLI interface is available as from firmware version 1.1.x.x Version 1.0.x.x 

and below only have a reduced interface (or less). For more information regarding a 
firmware upgrade see the Upgrade Firmware chapter. 

UPS Integration 

As of firmware version 1.3, your EnergySwitch PDU features UPS integration functionality.  
This enables the EnergySwitch to receive vital battery information from a connected UPS and 
perform actions when set parameters and rules are met. 
In order to use the full capabilities of the functionality, 2 components need to be installed and 
configured correctly: 
 

 

UPS Integration

 

The link with the UPS in the rack, as explained in this chapter. 
 

 

Agent Communication 

Communication with the Agent service on connected servers (for more details see the 
Agent Communication chapter). 

Configuration 

Compatible Devices 

The following UPS models can be linked to your EnergySwitch PDU: 
 

 

Most APC Smart-UPS® models (except Microlink enabled devices) 

Connecting the UPS 

The EnergySwitch and the UPS are connected using the following cable configuration: 
 
On the side of the 

EnergySwitch

: a standard RJ45 plug (with the pin layout as described in the  

 

Summary of Contents for ES2000 Seriesl





















































Reviews:

No comments