manualshive.com logo in svg

Racktivity ES2000 Seriesl, User Manual, Page: 15 / 52

Share
Download
Racktivity ES2000 Seriesl User Manual Download Page 15

© 2011 Racktivity NV 

 

15/52

 

Antwerpsesteenweg 19 - 9080 Lochristi - Belgium  -  www.racktivity.com 

v 2014.3.27 

Mounting the EnergySwitch 

1.

 

Attach the 2 mounting brackets to the back of the EnergySwitch using the provided screws. 
The brackets may be positioned for mounting on either side of the rack. 
 

 

2.

 

Attach the PDU to a vertical rail in your rack or rack enclosure. (Use the mounting hardware 
that came with your rack or rack enclosure to attach the mounting brackets to the rail.) 

Additional Earthing 

The metal case of the EnergySwitch is electrically bonded to the line cord 
ground wire. A threaded grounding point on the front of the case may be used 
as an additional means of protectively grounding this product and the rack. 

Connecting the EnergySwitch 

1.

 

For North America Connect the NEMA input plug to a compatible NEMA outlet receptacle.   

For Europe and other countries using IEC 309 based power receptacles, connect to the IEC 
309 receptacle compatible to the IEC 309 cord plug provided.   

Note: The AC power source should not share a circuit with a heavy electrical load.  It is 
recommended that the EnergySwitch be connected to a dedicated branch circuit.

 

2.

 

The POWER LED (blue) will become active. 

3.

 

When using the device for the first time all OUTPUT LEDs will light up consecutively 
indicating that the outlets are being activated. 

Connect your equipment’s input plugs to the outlet plugs of the EnergySwitch. 

 

 

Summary of Contents for ES2000 Seriesl





















































Reviews:

No comments