background image

 

16

BATTERY AND BATTERY CHARGE 

1. Battery 

Charge the equipped battery before using it, although it has already charged and can be used. 

 

Notes : 1.  Be sure to make correct connection with the battery terminals (

red, 

black). 

2. To connect the battery, start with the 

terminal, to disconnect it, start with the 

terminal. 

 

2. Battery Care 

(1)  The battery electrolyte is diluted sulfuric acid and is very harmful to the skin. Never unscrew the electrolyte cap except 

when required to refill. When refilling, pay enough attention to keep the electrolyte off the skin. Also, never to spill the 
electrolyte. 

(2)  The battery discharges continuously even not in use, so the supplementary charging is required. 

* Be sure to recharge the battery using the attached charger, because unlike automobile batteries, this battery cannot be 

charged during the operation. 

(3)  The attached charger is an automatic charger, which can automatically switch from the normal charging to the 

supplementary charging (charging to cover the self-discharged electricity). 

(4)  Check the electrolyte level from time to time. Put distilled water into the battery up to the maximum liquid level, if the 

electrolyte level is below the level. 

 

3. Battery Charging 

(1)  Clean the battery terminals, by removing dust and dirt from the 

battery. If the electrolyte level is below the maximum liquid level, 
put distilled water into the battery up to the maximum liquid level. 

(2)  Connect the output plug of the battery charger to the socket of 

this fire fighting pump. If the power switch is tuned on, the power 
lamp(red) is lit and the charging starts. 

(3)  The charging is complete when the completion lamp(green) is lit 

and the power lamp(red) is turned off. The charger goes into the 
supplementary battery charging. 

 

Notes : 1. The breaker is activated if excessive current is supplied because of a reverse connected battery. Also, the 

breaker may be activated if the Main Switch is turn to the "CELL" during the charging. Eliminate the causes 
of the problem, and reset the breaker to the normal position. 

2. The useful life of the battery is about 2 years. 

 

 

 

 

Charge status

 

Lit

 

 

Power lamp

(Red)

 

Completion 
lamp (Green)

Not charged 

 

 

 80% 

 

 

Normal 
charging

 

 80% 

 

○ 

Compensation charging

 

 

○ 

WARNING 

WARNING 

WARNING 

Summary of Contents for P455SM

























Reviews: