manualshive.com logo in svg

Quasonix Compact RDMS, Installation And Operation Manual, Page: 31 / 64

Share
Download
Quasonix Compact RDMS Installation And Operation Manual Download Page 31

 

Compact RDMS

TM

 Telemetry Receiver

 

17

 

Quasonix, Inc. 

 

Mnemonic 

Name 

Description 

 

Option (s) 

Required 

Basic or 

Advanced 

Command 

Mode 

Restriction

SY 

System Status 
Tracking 

Displays the system status 
of the receiver 

The first argument specifies 
the period, in milliseconds, 
between status updates. 
Zero (0) disables continuous 
monitoring. 

The second argument 
specifies the number of 
status lines between header 
output. 

Examples: 

SY Displays 

current 

status report settings 

SY 5 

Sets status output 

period to 5 milliseconds 

SY 5 100 

Sets status 

header output once every 
100 status updates 

 

The SY command reports 
system status information 
about the timing and 
frequency tracking loops, as 
well as mod scaling, lock 
indication and eb/n0 data. 
This command is very 
effective for troubleshooting 
link issues. 

Standard 

Advanced 
Command 

Available 
for all 
EXCEPT 
PSK 
(legacy) 

TO Tape 

Output 

Displays the status of the 
Tape Output option 

Example: 

TO Displays 

current 

tape output status settings 
(enabled/disabled and output 
frequency) 

37 

Advanced 
Command 

PCM/FM 

Summary of Contents for Compact RDMS

































































Reviews:

No comments