manualshive.com logo in svg

Quasonix Compact RDMS, Installation And Operation Manual, Page: 24 / 64

Share
Download
Quasonix Compact RDMS Installation And Operation Manual Download Page 24

 

Compact RDMS

TM

 Telemetry Receiver

 

10

 

Quasonix, Inc. 

 

Mnemonic 

Name 

Description 

 

Option (s) 

Required 

Basic or 

Advanced 

Command 

Mode 

Restriction

FR Frequency 

Report or set receiver center 
frequency 

Examples: 

FR          Report the 
frequency setting 

FR 2200.5   Set modulation 
to 2200.5 MHz 

Standard Basic 

None 

FS 

IF Filter Select  Report or set the current IF 

filter in the receiver 

FS  

Display 

the 

current IF filter 

FS A 

 

Set IF filter 

to automatic 

FS (0-7) 

Manually set 

IF filter (not recommended) 

Standard 

 

-14 option 
permits 7 
additional 
filters 

Basic None 

GO Start/Restart 

Apply changes then reset 
demodulator. 

Initiate demodulation with 
current parameters. This 
command is required when 
setting both the modulation 
and the bit rate. 

GO command is issued any 
time the bit rate is changed. 
This forces the demodulator 
to rescale all of its loop 
parameters and digital 
filtering so they are set 
properly for the bit rate. 

Standard Basic 

None 

HX 

eXtended 
Help 

Displays a full list of 
available commands 

Standard Basic 

None 

Summary of Contents for Compact RDMS

































































Reviews:

No comments