manualshive.com logo in svg

Quasonix Compact RDMS, Installation And Operation Manual, Page: 20 / 64

Share
Download
Quasonix Compact RDMS Installation And Operation Manual Download Page 20

 

Compact RDMS

TM

 Telemetry Receiver

 

6

 

Quasonix, Inc. 

 

For setup and configuration via a standard Windows-based PC, Quasonix recommends the application called 

Terminal

, a flexible, full-featured control interface that is included in the RDMS Product CD. Otherwise, one can 

use HyperTerminal, included with the standard Windows installation (Start -> All Programs -> Accessories -> 
Communications -> HyperTerminal). 

When power is applied to the receiver, the welcome message, shown in Figure 5, displays. 

 

 

Initializing... 
downconverter init... 
Quasonix Demod/Receiver Interface 
IRIG-106 Release 07 
6025 Schumacher Park Drive 
West Chester, Oh 45069 
(513) 942-1287 
www.Quasonix.com <http://www.Quasonix.com> 
CAGE CODE: 3CJA9 
FPGA Revision: 0x3132 0x0000 
PSK FW Revision: 2.0.043 7/29/2008 
PSK> 

Figure 5: RDMS™ Welcome Message 

 

All commands are one or two alphabetic characters, followed by 0, 1, or 2 arguments. If the command is issued with 
arguments, there must be a space after the alphabetic characters. The commands are not case sensitive. 

All commands generate a response of one or more lines. The length of the response depends on the verbosity level 
(set by the VL command). The last response line is always the currently selected mode (PCM/FM, SOQPSK, CPM, 
or PSK), followed by the character “+” or “>”, depending on the version of the firmware. This prompt signifies that 
the RDMS is ready to accept new characters. 

Summary of Contents for Compact RDMS

































































Reviews:

No comments