Quasonix Compact RDMS Installation And Operation Manual Download Page 21 | Manualshive

Page: 21 / 64

Quasonix Compact RDMS Installation And Operation Manual Download Page 21

Compact RDMS

TM

Telemetry Receiver

7

Quasonix, Inc.

4.3.1

Tier 0 (PCM/FM), Tier I (SOQPSK-TG), and Tier II (Multi-h CPM) Commands

The following table describes all receiver user commands. Listed are the command code, name, description of the
command, whether specific options must be ordered or the command is standard on all receivers, basic or advanced
command, and whether the command is restricted to specific waveform modes.

Note:

If a user issues a command that does not apply to a given mode, an "Invalid Command" message is displayed.

Any command that is valid in a mode but is disabled due to the option not being installed, returns an "Option Not
Installed" message.

Table 6: Standard and Optional User Commands

Mnemonic

Name

Description

Option (s)

Required

Basic or

Advanced

Command

Mode

Restriction

? Help

Message

Displays abbreviated list of
available commands

Standard Basic

None

AD

Downconvert
Antenna

AD Report

the

downconvert antenna state

AD 0

Set downconvert

antenna state to OFF
(Disabled)

AD 1

Set downconvert

antenna state to ON
(Enabled)

**Downconverting antenna
control only available when
using a 5-band
downconverter AND P and C
bands are available on the
unit. (applies to customers
using downconverting
antennas for C-band)

**Standard

Basic None

AE AGC

Enable

Enable or Disable Automatic
Gain Control (AGC)

Examples:

AE Report

AGC

state

AE 0

Set AGC state to

OFF (Disabled)

AE 1

Set AGC state to ON

(Enabled)

Standard Basic

None

«
...
19
20
21
22
23
...
»

Summary of Contents for Compact RDMS

































































Reviews:

No comments