23
06/21
7022-801H
CASTILE INSERT
F. Surround and Cast Trim Set
1. Place the peel and stick round felt vibration insulation
pads on the front side in each corner of the top metal
piece and on the back side in each corner of the top
cast piece
(Figure 23.1).
2.
Lay surround face down on a flat protected surface to
prevent scratching.
3. Using the Phillips screwdriver attach the side surrounds
to the top surround using 2 sheet metal screws
provided with the kit on each side.
4. Assemble Cast Trim and attach to surround:
a. Place corresponding cast trim pieces (2 cast trim
sides and 1 cast trim header) underneath the
surround set, also face down. Align the holes in
the metal pieces with the 5 bosses on the top
cast piece and 2 bosses on each side piece
(Figure 23.1)
.
b. Attach the magnets to the magnet brackets with
one countersink screw each. Attach magnet and
bracket to the metal surround sides with magnet
facing the front as shown in
Figure 23.1
.
c. Place cast footers under metal sides aligning the
top and bottom holes.
d. The 9 mounting clips are shipped in one long strip.
Use your hands or pliers to break them apart.
6.
Install the power cord in the surround:
-
If power enters the appliance on the right side:
Using the pliers, attach cord restraint 12 inches
from the female end of the cord and then press into
the right side panel.
-
If power enters appliance on the left side:
The
cord will have to be routed through the back of
the insert. When routing the power cord, keep
cord lying flat as possible, keeping the cord away
from all exhaust surfaces and moving parts. After
routing, install cord restraint and press into the left
side panel.
7. Slide surround over the top of the insert into place.
Surround attaches to bottom and top of insert sides
with the supplies 1/4 inch screws.
8. Plug cord into inlet on junction box routing the wire.
9. Install plug into unused hole.
(4) Felt Vibration
Insulation Pads
Secure
Surrounds
to Cast
Trim Kit
Attach Magnet
before install-
ing Cast
Footers
Magnet Installed
Cast Footers:
Left and Right
Back
of
Side
Piece
Magnet Attached - Faces Front
Clearance Notch
Figure 23.2
Figure 23.3
Figure 23.1
Surround Set
attaches to top
and bottom of
insert sides.
Thumb
Screw
Bracket
Figure 23.4
NOTE:
The right cast side bracket has the hopper cut out
switch attached. Remove the retainer from the
right side and allow to hang down into the insert
or disconnect the switch when removing side.
5.
Remove the cast sides before attaching the surround
and trim. Lift up the top to expose the thumb screws
that secure the cast sides. Remove the thumb screw
and top bracket and then remove the cast side.
e. Each clip has a clearance notch to allow room for
the cast on the boss. Place the clips over the boss
so that the notch is facing the outer edge of the
surround
(Figure 23.3)
.
f.
It is best to install all of the 1/4-20 screws only
half way at first to allow for adjustments. After
adjustment tighten the 2 screws in each footer first
and then work your way around to the rest.
Summary of Contents for CASTILEI-MBK-C
Page 28: ...28 06 21 7022 801H CASTILE INSERT Date of Service Performed By Description of Service ...
Page 29: ...29 06 21 7022 801H CASTILE INSERT Date of Service Performed By Description of Service ...
Page 30: ...30 06 21 7022 801H CASTILE INSERT Date of Service Performed By Description of Service ...
Page 31: ...31 06 21 7022 801H CASTILE INSERT Date of Service Performed By Description of Service ...
