QTech QSW-6200-32T Hardware Installation And Reference Manual Download Page 42 | Manualshive

Page: 42 / 56

background image

QSW-6200

Series Switch Hardware Installation and Reference Guide

42

www.qtech.ru

Ventilation System Maintenance



The fan in the equipment responsible for heat dissipation is provided with the fault monitoring signals. When the

fan fails, a corresponding alarm will occur.



Replace the faulty fan with a qualified one.



Tighten the captive screws of the fan module.

Power Supply Maintenance

When the power supply fails, you only need to disconnect the power cable, unplug the power module, replace it with a

qualified one, and then connect the power cables tightly.

Replacing Lithium Battery

The built-in lithium batteries can support the real time clock of the QSW-6200 switch without external power supply.

Please contact the TAC of QTECH for replacing lithium batteries. Technical staff of QTECH will replace the battery of the

same model.

Replacing Fuses

Please contact the TAC of QTECH for replacing fuses. Technical staff of QTECH will replace the fuse of the same model.

«
...
40
41
42
43
44
...
»

Summary of Contents for QSW-6200-32T

























































Reviews:

No comments

Related manuals for QSW-6200-32T

Brand: Radial Engineering Pages: 12

Brand: Magnetrol Pages: 12

Brand: Magnimage Pages: 53

LambdaUnite MSS

Brand: Lucent Technologies Pages: 388

SmartNode 4658 Series

Brand: Patton electronics Pages: 12

Brand: Setra Systems Pages: 4

Brand: TRENDnet Pages: 12

Brand: Zamel Pages: 2

Brand: Exsys Pages: 14

Brand: UniFi Pages: 8

Brand: Digitronic Pages: 24

Brand: Tenda Pages: 177

Brand: Versa Technology Pages: 26

Brand: Cable Electronics Pages: 12

Signal Distribution Box SDB45

Brand: Audiovox Pages: 12

DHS-LIT-SWP-DHS

Brand: Digital Home System Pages: 2

ProSAFE FS526Tv2

Brand: NETGEAR Pages: 20

Brand: Scion-Tech Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands