QTech QSW-6200-32T Hardware Installation And Reference Manual Download Page 8

Page: 8 / 56

QSW-6200

Series Switch Hardware Installation and Reference Guide

www.qtech.ru

Note:

1. Grounding connector

2. Expansion module slot 1

3. Expansion module slot 2

4. Power module slot 1

5. Power module slot 2

Power Supply

QSW-6200-32T supports 2 power modules. For details, see the section

“Power Modules”.

Dual-power input: The switch can be powered by one power module, or two power modules. When both two modules are

available, the switch is powered in current sharing mode.

When the switch is powered by the dual-power modules, if the system working power is greater than the capacity of

single power module, power redundancy cannot work; if one power module fails, the switch system will be affected.

Heat Dissipation

The QSW-6200-32T is designed with left and right fans for heat dissipation, thereby ensuring the normal function of the

device in the specified environment. Maintain a minimum clearance of 10cm around the chassis to allow air circulation.

Figure 1-4 Flow Scheme of Heat Dissipation

LED

Summary of Contents for QSW-6200-32T

























































Search results

Summary of Contents for QSW-6200-32T

Reviews:

Related manuals for QSW-6200-32T

Brands by name

Popular brands

QTech QSW-6200-32T, Hardware Installation And Reference Manual

Search results

Summary of Contents for QSW-6200-32T

Reviews:

Related manuals for QSW-6200-32T

Brands by name

Popular brands