QTech QSW-6200-32T Hardware Installation And Reference Manual Download Page 30

Page: 30 / 56

QSW-6200

Series Switch Hardware Installation and Reference Guide

www.qtech.ru

3 Product Installation

Please ensure that you have carefully read Chapter 2 and make sure that the requirements set forth in Chapter 2

have been met.

3.1 Installation Flowchart



Mount the switch to the rack



Connect the system grounding



Connect the power supply



Connect interface cables



Bundle the power cables or optical fibers



Installation check

3.2 Pre-installation Confirmation

Before installation, please confirm the following points:



Whether sufficient airflow is available for the switch



Whether the requirements of the switch for temperature and humidity are met



Whether power cables are already laid out and whether the requirements of electrical current are met



Whether related network cables are already laid out

3.3 Installing the Switch

Precautions

During installation, note the following points:



Connect the power cables of different colors to the corresponding grounding posts.



Ensure that the connected power cables have sound contact.



Do not place heavy items on the switch.



Reserve a spacing of at least 10 cm around the chassis for good ventilation. Do not stack the devices.



The switch should be located far away from the large power radio launch pad, radar launch pad, and

high-frequency large-current devices. If necessary, electromagnetic shielding should be adopted. For example,

use interface cables to shield cables.



Interface cables should be laid inside the equipment room. Outdoor cabling is prohibited, avoiding damages to

Summary of Contents for QSW-6200-32T

























































Search results

Summary of Contents for QSW-6200-32T

Reviews:

Related manuals for QSW-6200-32T

Brands by name

Popular brands

QTech QSW-6200-32T, Hardware Installation And Reference Manual

Search results

Summary of Contents for QSW-6200-32T

Reviews:

Related manuals for QSW-6200-32T

Brands by name

Popular brands