QRPGuys Digital DSB II Transceiver Kit Instructions Manual Download Page 16 | Manualshive

Page: 16 / 16

QRPGuys Digital DSB II Transceiver Kit Instructions Manual Download Page 16

Page 16 of 16 ft8_II_assy_smd_diode_072020.pdf

In the table below are some “modeled” values for additional bands to experiment with. Some
tweaking may be required. You will need to source your own components. If you choose to model
your own high pass filter (L1 & C26), be sure to add the 88pF stray capacitance inherent in the
design to C26. That has been done with the modeling you see below.

Notes:

_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________
_________________________________________________

«
...
14
15
16

Summary of Contents for Digital DSB II Transceiver Kit

















Reviews:

No comments