INSTALLATION AND OPERATION MANUAL SOLAR MODULES Q.PEAK DUO BLK-G10+ / HL
INSTALLATION AND OPERATION MANUAL SOLAR MODULES Q.PEAK DUO BLK-G10+ / HL
4
5
1 Introduction
Validity
These instructions are only valid for crystalline solar modules
from the company Q CELLS as specified at chapter „2.1 Technical
Specifications“. Q CELLS assumes no liability for damage resulting
from failure to observe these instructions.
Please observe the wiring and dimensioning of the system.
The installer of the system is responsible for compliance with
all necessary safety regulations during set-up and installation.
Q CELLS assumes no liability on the basis of these instructions.
Q CELLS is only liable in the context of contractual agreements or
in the context of accepted guarantees. Q CELLS accepts no other
responsibility for the functionality and safety of the modules.
Please observe the instructions for any other system compo-
nents that may be part of the complete solar power system. It
may be necessary to carry out a structural analysis for the ent-
ire project.
If your questions are not satisfactorily answered in the manual,
please contact your system supplier.
Information for the Operator
Please keep this installation manual for the entire life of the
solar power system.
Please contact your system supplier for information concerning
the formal requirements for solar power systems.
Please be sure to contact the relevant local authorities
and energy providers regarding regulations and permit
requirements prior to installation of the solar power system.
Your financial success depends on the fulfillment of these
requirements.
Other applicable documents
This installation manual is only valid in combination with the
following technical information.
Document type
Product data sheet
Packaging and transport information
MISUSE OR INCORRECT USE OF SOLAR MODULES VOIDS
THE LIMITED WARRANTY AND MAY CREATE A SAFETY
HAZARD AND RISK PROPERTY DAMAGE. THIS INCLUDES
IMPROPER INSTALLATION OR CONFIGURATION, IM PROPER
MAINTENANCE, UNINTENDED USE, AND UNAUTHORIZED
MODIFICATION.
2 Planning
2.1 Technical specifications
For additional information see the relevant datasheet of the module provided at www.qcells.com.
PRODUCT LINE
Q.PEAK DUO BLK-G10+ / HL
Type
Q.ANTUM DUO Z
Length [in]
67.6 (1717 mm)
Width [in]
41.1 (1045 mm)
Frame height [in]
1.57 (40 mm)
Area [yd²]
2.14 (1.79 m²)
Weight [lbs]
46.3 (21.0 kg)
Max. system voltage V
SYS
1000 V
Max. reverse current
20 A
Permissible temperature range
–40 °F to +185 °F (–40 °C to +85 °C)
Junction box protection class
IP67 with bypass diode
Connector protection class
IP68
Fire rating based on ANSI / UL 61730 TYPE 2
Max. test load Push / Pull
1
[lbs/ft
2
]
125 / 113 (6,000 Pa / 5,400 Pa)
Max. design load Push / Pull
1
[lbs/ft
2
]
83 / 75 (4,000 Pa / 3,600 Pa)
Certificates
Quality Controlled PV by TÜV Rheinland; CE-compliant; IEC 61215:2016; IEC 61730:2016;
PV module classification: Class II; UL 61730
1
Test and design load in accordance with IEC 61215:2016, depending on mounting options (see section "2.3 Mounting options")
NA
DETAIL A
0.63" (16 mm)
0.33" (8.5 mm)
0.837" (21.25 mm)
38.6" (980 mm)
67.6" (1717 mm)
4 × Mounting slots
(DETAIL A)
Frame
41.1" (1045 mm)
39.5" (1002,5 mm)
1.57" (40 mm)
8 × Drainage holes
14.5“ (368.5 mm)
4 × Grounding points ø 0.18" (4.5 mm)
Label
≥
45.3" (1150 mm)
≥
45.3" (1150 mm)
Fig. 1:
External dimensions and components for Q.PEAK DUO BLK-G10+ / HL
