background image

16

17

INSTALLATION AND OPERATION MANUAL SOLAR MODULES Q.PEAK DUO BLK-G6+ / AC – Q CELLS

INSTALLATION AND OPERATION MANUAL SOLAR MODULES Q.PEAK DUO BLK-G6+ / AC – Q CELLS

17

Module Selection

For detailed key electrical data, refer to the product data sheet for 
the respective product (available at www.q-cells.us). 

Safety Factor

During normal operation, a module may generate a greater current 
and / or higher voltage than that determined under standardized test 
conditions. Accordingly, the values of I

SC

 and V

OC

 marked on the 

module should be multiplied by a factor of 1.25 when determining:

• 

the component voltage ratings

• 

conductor ampacities

• 

fuse sizes

• 

size of controls connected to the PV output

Refer to Section 690-8 of the National Electrical Code for an 
additional multiplying factor of 125 percent (80 percent derating) 
which might be applicable.

 

Ä

Follow the valid national guidelines for the installation of electrical 
systems (refer to section 690-8 of the NEC for an additional 
multiplying factor of 125 percent [80 percent derating] which 
may be applicable).

Module Connection

Detailed information about interconnecting modules are specified 
in section "9 Appendix" on page 28.

NOTE! 

When installing different product versions, the lowest minimum 
permitted reverse current load capacity applies. 

2  PLANNING

2.6 ELECTRICAL LAYOUT

3  INSTALLATION

3.1  SAFETY AND TRANSPORT

 

Ä

Leave modules in their original packaging until 
installation. 

 

Ä

Store the modules securely in cool and dry rooms. 
The packaging is not weatherproof.

 

Ä

Inspect the packaging for damages.

 

Ä

Contact the transport company regarding 
any damage to the packaging and follow their 
instructions.

 

Ä

Follow any instructions on the packaging.

 

Ä

Ensure that all personnel are aware of and adhere 
to accident-prevention and safety regulations.

 

Ä

While working wear clean gloves.

§

GB

§

I

§

D

DANGER! Risk of fatal injury due to electric shock! 

 

Ä

Do not install damaged modules.

 

Ä

Inform your vendor of any damages 
immediately.

WARNING! Fire Risk!

 

Ä

Do not install modules indoors.

 

Ä

Do not install modules on moving objects.

 

Ä

Do not use Enphase equipment in a manner not 
specified by the manufacturer. Doing so may 
cause death or injury to persons, or damage to 
equipment.

Summary of Contents for Q.PEAK DUO BLK-G6+/AC


























Reviews: