background image

36

37

INSTALLATION AND OPERATION MANUAL SOLAR MODULES Q.PEAK DUO BLK-G6+ / AC – Q CELLS

INSTALLATION AND OPERATION MANUAL SOLAR MODULES Q.PEAK DUO BLK-G6+ / AC – Q CELLS

 

 

Installation and Operation Manual 

 

 2020 Enphase Energy Inc. All rights reserved. 

 

 

17 

Step 5: Mount the ACMs 

You can use clamps or module mounting holes to mount the modules on the installation or you can use 

an embedded system. If using an alternative mounting solution, contact to be sure that is covered by 

the warranty. Refer to the mounting options on pages 14 and 15 for more information.

 

 

A.  Install the ACM with a clearance of at least 10 cm (4 in.) from the roof. Also, make sure that the 

microinverter on the underside of the ACM is at least 1.9 cm (0.75 in.) away from the roof or 

installation surface. 

B.  Do not place the ACMs in such a way that places pressure on the microinverter. Minimum 

distance from the top edge of the module to the rail should be about 270 mm (11.02 in.). 

C.  Make sure that the minimum gap between modules is 10 mm (0.4 in.) or greater. 
D.  Check that rails and clamps are clear of the microinverter by at least 3.8 cm (1.5 in.). Do not 

obstruct module drain holes. 

 

Step 6: Connect the Microinverters as you Install the ACMs 

A.  Check again that the ACMs are not placing pressure on the microinverter. Minimum distance from 

the top edge of the module to the rail should be about 30 cm (12 in.). 

B.  As you install each ACM, connect the Q Cable to the microinverter. Listen for a click as the 

connectors engage. 

C.  Cover any unused connectors on the AC cable with Enphase Sealing Caps. Listen for a click as 

the sealing caps engage. 

 

WARNING

: Risk of electric shock. Risk of fire. Install sealing caps on all unused AC 

connectors as these connectors become live when the system is energized. Sealing caps 

are required for protection against moisture ingress. 

 

 

Step 7: Manage the Cabling 

A.  Use cable clips to attach the cable to the module frame. Leave no more than 1.8 m (six feet) 

between cable clips. 

 

Cable clip 

B.  Dress any excess cabling in loops so that it does not contact the roof. Do not form loops smaller 

than 12 cm (4¾ “) in diameter. 

 

 

Installation and Operation Manual 

 

 2020 Enphase Energy Inc. All rights reserved. 

 

 

18 

Step 8. Ground the ACMs 

Choose to use grounding clamps or module mounting holes to ground the modules. Or, you can use a 

reliable third-party grounding system. 

 

All Methods: 

A.  Ground the module frames to protect the array from lightning and static-electricity damage using 

Method A, B, or C. 

B.  Be sure that the grounding device will fully contact the inner side of the aluminum alloy and 

penetrate the frame surface oxide film. 

C.  Make a connection from the grounding conductor to earth using a suitable earth ground 

electrode. 

WARNING

: Risk of equipment damage. Do not drill additional grounding holes on module 

frame. The module frame has been drilled and marked for grounding. Use the Grounding 

holes only for grounding, and do not used them for mounting or other purposes. 

 

NOTE

: The grounding conductor or strap can be copper, copper alloy, or any other 

material acceptable for use as an electrical conductor per the National Electrical Codes. 

The grounding wire material and size must meet all local and regional requirements. 

 

Method A: Grounding with grounding clamps. 

  Locate the grounding hole (diameter Ø4 mm) at the edge of the module frame back. 

  Use 12 AWG copper core wire for the grounding clamp, and do not damaged the copper wire 

during installation. 

  Torque to 2.3N•m. 

 

 

 

 

 

 

 

 

Method B: Grounding with unused mounting holes. 

You can use the frame edge grounding holes or unused 

mounting holes on the  ACM for installing grounding 

devices. 

  Align a grounding clamp to the frame hole 

and place a grounding bolt through the 

grounding clamp and frame. 

  Place the toothed side of the washer as 

shown and fasten the nuts. 

 

  Place the grounding wire through the 

grounding clamp and tighten the nuts. 

 

 

 

Method C: Grounding with third party hardware. 

You can use third party grounding devices for grounding of solar modules, but these devices must be 

reliable and must be operated per manufacturer instructions. 

 

wire slot

Method A

 

 

 

frame 

 

 

 

 

Method B

 

 

wire

 

 

locking nut

 

 

Summary of Contents for Q.PEAK DUO BLK-G6+/AC


























Reviews: