26
27
INSTALLATION AND OPERATION MANUAL SOLAR MODULES Q.PEAK DUO BLK-G6+ / AC – Q CELLS
INSTALLATION AND OPERATION MANUAL SOLAR MODULES Q.PEAK DUO BLK-G6+ / AC – Q CELLS
27
DANGER!
Risk of fatal injury due to electric shock!
Ä
Do not attempt to fix any problems yourself (e.g., glass cracks,
damaged cables).
Ä
Contact an installer or Q CELLS Technical Customer Service
Department.
Ä
Do not disconnect modules yourself.
Ä
Commission a trade specialist.
Ä
Dispose of modules in accordance with the local disposal
regulations.
6 FAULTS AND DEFECTS
7 DISPOSAL
5 GROUNDING
Option B: Grounding Methods
Q CELLS modules can be bonded and grounded with a racking
system certified to UL 2703 for Bonding and Grounding that has
been evaluated and listed as compatible with Q CELLS modules.
In such cases the entire system can be appropriately bonded and
grounded when installed per the racking systems instructions with
appropriate system grounding.
Q CELLS Modules are generally compatible with Racking Integrated
Bonding solutions, but the racking UL 2703 Listing and Installation
manual should be checked to insure the module is Listed. Examples
of integrated bonding solutions would be Wiley WEEB
®
washers or
IronRidge’s UFO, some of these products can be used multiple times
or only once before requiring replacement. Refer to the Racking
Manufacturers installation manual for instructions on installation
and replacement. Refer to Wiley’s installation instructions for the
specific use of WEEB washers.
PV Laminate
Backing Nut (Stainless Steel)
Toothed Lock Washer (Stainless
Steel)
Grounding Lug (Stainless Steel
or tin-plated metal)
Equipment
Grounding
Conductor
Aluminum
Frame
Screw (Stainless Steel)
Q CELLS solar modules are known for a long operating life and
minimal maintenance effort and expense. Dirt and grime are usually
washed away by rain. If the module is fully or partially shaded by
dirt or debris (e.g., plants, bird droppings), it needs to be cleaned
to prevent a loss of performance.
Maintenance
Ä
The PV system has to be inspected regularly by certified
personnel.
Ä
The time intervals and extent of the inspection can depend on
local circumstances (e.g., salt, ammonia content in the air, high
humidity etc.). The customer/operator must inform him / herself
about time intervals and extend of necessary inspections.
Ä
Inspections must be performed especially after extraordinary
events (e.g., storm, hail, high snow loads etc.)
Ä
During the inspections, it has to be checked that the components
are secure, undamaged and clean.
Cleaning
WARNING!
Risk of injury due to hot and live modules!
Ä
Only clean modules that have cooled down.
Ä
Do not carry or wear any electrically conductive parts.
WARNING!
Risk of falling due to unsecured access!
Ä
Never access the installation area alone or without taking ade-
quate security precautions.
Ä
Commission a trade specialist.
NOTE!
Module surface damage may occur!
Ä
Remove snow and ice carefully without force (e.g., with a very
soft broom).
Ä
Do not scratch off dirt.
Ä
Rinse dirt (dust, leaves, etc.) off with lukewarm water or use, only
for the glass surface, an alcohol based glass cleaner. Do not use
abrasive detergents or surfactants for any part of the panel.
Ä
Use a soft cellulose cloth (kitchen roll) or sponge to carefully wipe
off stubborn dirt. Do not use micro fleece wool or cotton cloths.
Isopropyl alcohol (IPA) can be used selectively to remove stubborn
dirt and stains within one hour after emergence.
Ä
Follow the safety guidelines provided by the IPA manufacturer.
Ä
Do not let IPA run down between the module and the frame or
into the module edges.
NOTE! Module damage may occur!
Ä
Do not clean modules with water if there is a risk of
frost.
0°
8 MAINTENANCE AND CLEANING
Ä
Free the substructure from any dirt and debris
(leaves, bird nests, etc.).
Ä
Remove dirt with lukewarm water or alcohol based
glass cleaner, a broom, or a soft cloth.
Ä
Do not use surfactants, rotating brushes, scrapers,
or any high-pressure water cleaning equipment.
