DENALI 28
2.8 Control Systems Maintenance
Control Maintenance
Periodic inspection of the control systems and all connections should be made. Signs of rust,
corrosion, wear, or other deterioration should immediately be serviced. Generally, periodic
lubrication of all moving parts and connections with a light waterproof grease is in order.
Lubrication should be performed as often as necessary to keep the system operating smoothly.
Control system adjustments may become necessary. If adjustment becomes necessary, see your
Pursuit dealer.
DO NOT ATTEMPT CONTROL ADJUSTMENTS UNLESS YOU ARE FAMILIAR WITH SER-
VICING CONTROL SYSTEM PROCEDURES. CONTROL MISADJUSTMENT CAN CAUSE LOSS
OF CONTROL AND SEVERE ENGINE OR OUTDRIVE DAMAGE.
Steering System Maintenance
A periodic inspection of all steering hoses, linkage and helm assemblies should be made. Signs of
corrosion, cracking, loosening of fastenings, excessive wear, or deterioration should be immedi-
ately corrected. Failure to do so could lead to steering system failure that would result in loss of
control.
The engine driven power steering system has specific fluid and maintenance requirements. Please
refer to the engine owner's manual for maintenance information on the power steering system.
Trim Tab Maintenance
Marine growth can interfere with the proper operation of the trim tab planes and actuators. To
reduce problems due to marine growth, always return the trim tabs to the full “UP” position after
operating the boat and periodically inspect and clean marine growth from the actuators and planes.
The trim tab fluid should be checked often. Keep the fluid level between the marks on the trim tab
pump reservoir with the trim planes in the up position.
If your Denali will be left in saltwater for extended periods it may be necessary to install zinc anodes
on the trim tab planes to prevent galvanic corrosion. Refer to the trim tab owner's manual for
additional maintenance information and fluid specifications.
FAILURE TO PROPERLY INSPECT AND MAINTAIN THE STEERING AND CONTROL SYS-
TEMS CAN LEAD TO A CONTROL SYSTEM FAILURE AND LOSS OF CONTROL. MAKE
SURE YOU INSPECT AND SERVICE THE STEERING AND ENGINE CONTROL COMPONENTS
FREQUENTLY.
2-5
Summary of Contents for Denali 28
