DENALI 28
•
Before operating the boat for the first time, read the engine break-in procedures. The break-
in procedures are found in the owner’s manual for the engine. The manual is in the literature
packet.
•
As different types of engines could be used to power the boat, have the dealer describe the
operating procedures for your boat. For more instructions on “How To Operate The Boat,”
make sure you read the instructions given to you in the owner’s manual for the engine installed
in your boat.
Note: For more instructions on safety, equipment and boat handling, enroll in one of the
several free boating courses offered. For information on the courses offered in your
area, call the “Boating Safety Hotline”, 800-368-5647 or the “Boat U.S. Foundation
Course Hotline,” 800-336-2628 for further information on boating safety courses.
Note: If the drive unit hits an underwater object, stop the engine. Inspect the drive unit
for damage. If the unit is damaged, contact your dealer for a complete inspection
and repair of the unit.
To stop the boat, follow this procedure:
•
Allow the engines to drop to the idle speed.
•
Make sure the shifting levers are in the neutral position.
Note: If the engines have been run at high speed for a long period of time, allow them to cool
down by running the engines in the idle position for 3 to 5 minutes.
•
Turn the ignition key(s) to the “OFF” position.
After Operation:
•
If operating in saltwater, wash the boat and all equipment with soap and water.
•
Check the bilge area for debris and excess water.
•
Fill the fuel tank to near full to reduce condensation.
•
Check that the boat is properly moored.
•
Turn off all electrical equipment except the automatic bilge pumps.
•
If you are going to leave the boat for a long period of time, put the battery main switches in the
“OFF” position and close all sea cocks.
•
Make sure the boat is securely moored.
10-6
Summary of Contents for Denali 28
