PureTools PT-PMS-62S User Manual Download Page 38 | Manualshive

Page: 38 / 64

background image

User Manual

PT-PMS-62S

32

Now you are in the main view, where commands are sent and feedback is received.

The next step is to select the correct COM port of the PC. To do this, double-click on
"COM1" in the corresponding setup window.

In the following window, select the drop-down menu labeled "Send / Receive on
Comm Channel", select the appropriate COM port and then click on "OK" at the
bottom right corner.

All other settings can be left at default for most applications, but refer to device
RS232 settings to be sure.

Double clicking on

“COM1” to change to

the right COM port.

«
...
36
37
38
39
40
...
»

Summary of Contents for PT-PMS-62S

































































Reviews:

No comments

Related manuals for PT-PMS-62S

COOPER POWER SERIES

Brand: Eaton Pages: 32

Brand: Keithley Pages: 452

DynaGST/2402G GEP-33224T-1

Brand: UNICOM Pages: 1

Cleveland Controls RSS-498-013

Brand: UNICONTROL Electronic Pages: 2

Brand: United Electric Controls Pages: 6

LINK 14201-20 - DATASHEET FOR TOSHIBA PHONES

Brand: Jabra Pages: 4

Brand: Perel Pages: 4

Brand: Cablematic Pages: 8

Brand: GarrettCom Pages: 63

Brand: UniFi Pages: 8

Elinx EIR418-2SFP-T

Brand: B&B Electronics Pages: 25

Brand: CIS Pages: 3

Edison Cooper Power Series

Brand: Eaton Pages: 12

Brand: steute Pages: 20

ToolBox GTB-MHDMI1.3-441

Brand: Gefen Pages: 25

Brand: PRO SIGNAL Pages: 4

Brand: Scion Pages: 8

Brand: Campbell Hausfeld Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands