PureTools PT-PMS-62S User Manual Download Page 51

Page: 51 / 64

User Manual

PT-PMS-62S

Command

Description

Example and Feedback

CECI[port]4B.

Forward.

CECI014B.
[CEC]: blue ray skid forward.

CECI[port]4C.

Backward.

CECI014C.

[CEC]: blue ray skid backward.

CECI[port]6C.

Power off.

CECI016C.
[CEC]: Source Power off.

CECI[port]6D.

Power on.

CECI016D.
[CEC]: Source Power on.



Control the output display:

Command

Description

Example and Feedback

CECO[port]34.

Input channel selection.

CECO0634.
[CEC]: TV input select

CECO[port]41.

Volume up.

CECO0641.
[CEC]: TV VOL +

CECO[port]42.

Volume down.

CECO0642.
[CEC]: TV VOL -

CECO[port]43.

Mute

CECO0643.

[CEC]: TV VOL Mute

CECO[port]36.

Power off.

CECO0636.

[CEC]: TV Power off

CECO[port]04.

Power on.

CECO0604.
[CEC]: TV Power on

Summary of Contents for PT-PMS-62S
































































Search results

Summary of Contents for PT-PMS-62S

Reviews:

Related manuals for PT-PMS-62S

Brands by name

Popular brands

PureTools PT-PMS-62S, User Manual

Search results

Summary of Contents for PT-PMS-62S

Reviews:

Related manuals for PT-PMS-62S

Brands by name

Popular brands