PureTools PT-PMS-62S User Manual Download Page 49

Page: 49 / 64

User Manual

PT-PMS-62S

8.2.10

CEC Control

If the input sources and displays support CEC, they can be controlled by sending
CEC commands to replace IR remote.

Step 1:

According to the below command to enable CEC control.

Command

Description

Feedback Example

CECON.

Enable CEC

CEC Turn ON!

CECOFF.

Disable CEC

CEC Turn OFF!

Step 2:

According to the below command format to send specific command to

control input source or display device.

CEC [I/O][port][command].



The “

[I]

” represents the input port. The “

[O]

” represents the output port.



The “

[port]

” represents the port number. The input ports are 01~03, and the

output ports are 04~06.

Input Port

1.HDMI

2.HDMI

3.HDMI

Output Port

1.HDMI

2.HDMI (Loop)

2.HDBT



The “

[command]

” represents the specific command from the table below.\

Summary of Contents for PT-PMS-62S
































































Search results

Summary of Contents for PT-PMS-62S

Reviews:

Related manuals for PT-PMS-62S

Brands by name

Popular brands

PureTools PT-PMS-62S, User Manual

Search results

Summary of Contents for PT-PMS-62S

Reviews:

Related manuals for PT-PMS-62S

Brands by name

Popular brands