PureTools PT-PMS-62S User Manual Download Page 43

Page: 43 / 64

User Manual

PT-PMS-62S

Command

Description

Feedback Exam

%9971.

Report the connection status of all
inputs.
Y means the corresponding input port is
connected to a source device, N means
not.

In      01 02 03 04
Connect    Y Y N N
In      05 06
Connect    N N

AutomationON[X].

Enable the auto switching mode for the
output [X].

Output Port

HDMI

HDBT

HDMI Automation ON

HDBT Automation ON

AutomationOFF[X].

Disable the auto switching mode for the
output [X].

Output Port

HDMI

HDBT

HDMI Automation OFF

HDBT Automation OFF

8.2.3

Preset Setting

Command

Description

Feedback Example

Save[y].

Store the current switching status to
preset [y]. y=0~ 9.

Save To F0

Recall[y].

Recall the preset [y]. y=0~ 9.

Recall From F0

Clear[y].

Clear the preset [y].

Clear F0

8.2.4

Audio Control

Command

Description

Feedback Example

Embedded:[x].

Select external balanced audio (L+R) for
input [x]. x=1~2.

HDMI1 Embedded

UnEmbedded:[x].

Select internal audio for input [x].
x=1~2.

HDMI1 UnEmbedded

MIXOUT:[x].

The output [x] audio is mixed with MIX
audio.

HDMI1 OUT MIX

Summary of Contents for PT-PMS-62S
































































Search results

Summary of Contents for PT-PMS-62S

Reviews:

Related manuals for PT-PMS-62S

Brands by name

Popular brands

PureTools PT-PMS-62S, User Manual

Search results

Summary of Contents for PT-PMS-62S

Reviews:

Related manuals for PT-PMS-62S

Brands by name

Popular brands