PureTools PT-PMS-62S User Manual Download Page 41

Page: 41 / 64

User Manual

PT-PMS-62S

8.2

RS232 Communication Command

Communication protocol:

RS232 Communication Protocol

Baud rate: 9600 Data bit: 8 Stop bit: 1 Parity bit: none

Note:



In the commands, “[”and “]” are symbols for easy reading and do not need to be

typed in actual operation.



Please remember to end the commands with the ending symbols “.” or “;”.



Type the command carefully, it is case-sensitive.

8.2.1

Device Control

Command

Description

Feedback Example

PWON.

Power on system.

PWON

PWOFF.

Power off system. Turn off HDBaseT
power supply.

PWOFF

STANDBY.

System standby. Press any button to
awake.

STANDBY

/*Type;

Report system model.

PT-PMS-62S

/^Version;

Report firmware version.

V1.0.0

/%Lock;

Lock front panel buttons.

System Locked

/%Unlock;

Unlock front panel buttons.

System Unlock!

%9964.

Report IP address.

IP:192.168.0.178

USBUpdata:[x].

Upgrade the 3458 IC of the port [x].

Port

1~6

Input port

7~8

Output port

%9961.

Report the system locking status.

System UnLock/Lock!

%9962.

Report the system power status.

PWON/PWOFF

%0911.

Reset to factory default.

Note:

The switcher must be restarted after

factory reset to ensure signal output.

Summary of Contents for PT-PMS-62S
































































Search results

Summary of Contents for PT-PMS-62S

Reviews:

Related manuals for PT-PMS-62S

Brands by name

Popular brands

PureTools PT-PMS-62S, User Manual

Search results

Summary of Contents for PT-PMS-62S

Reviews:

Related manuals for PT-PMS-62S

Brands by name

Popular brands