Puretec HYBRID R10 User Manual Download | Manualshive

Page: 10 / 20

background image

10

Installation & Operation Manual

Copyright © Puretec Pty Ltd 2018

Operation

• Allow two minutes for the UV lamp to reach full intensity before starting water flow.

• On a new installation where no other form of sterilisation has been in use, we

recommend flushing the pipe work with a suitable sanitiser such as TankSafe (for
dosage refer to TankSafe product instructions). This solution should be left in the

pipework for at least an hour and preferably overnight.

The sanitising solution can be added into the water tank or if necessary added as

a shock dose into the bowl of the filter housing of the Hybrid-R Triple and slowly
flushed through the piping. If added as a shock dose the system and pipework

should be rinsed thoroughly by opening a downstream tap.

Operation

«
...
8
9
10
11
12
...
»

Summary of Contents for HYBRID R10





















Reviews:

No comments

Related manuals for HYBRID R10

Brand: Vagner Pool Pages: 16

Brand: HQRP Pages: 37

Brand: RainSoft Pages: 6

Brand: Reliable Pages: 4

Brand: Salus Pages: 2

Brand: DAB Pages: 228

Brand: 3M Pages: 113

SOLA-TECS 0200272

Brand: Cleantecs Pages: 7

Thunder CQE-CT-00142

Brand: Crystal Quest Pages: 4

Brand: Intex Pages: 17

MarinePRO RO System

Brand: SpectraPure Pages: 24

Brand: Arkal Pages: 34

Brand: A.O. Smith Pages: 20

Brand: Sime Pages: 29

LaboStar 7 TWF-DI

Brand: Siemens Pages: 43

Brand: Graco Pages: 20

Brand: Aqua Pages: 11

BADU Star 69/12

Brand: Speck pumpen Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands