manualshive.com logo in svg

PTI security systems VP keypad controls entry, Installation And Operation Manual

Share
Download
PTI security systems VP keypad controls entry Installation And Operation Manual Download Page 12

9

8 

Single Bollard

A bollard is used as an attractive and functional stand for 

keypads. It helps protect the keypad from being struck by 

vehicles. It can be used in driveways for vehicle access 

or near doors as a decorative keypad stand. It can be 

painted any color to compliment the site. Mounting height 

is determined by the height of the pipe on which it is 

mounted. 

Double Bollard

Similar in design to the single bollard, the 

double bollard is taller and has a second 

mounting point above the first to allow both 

cars and RVs to enter through the same 

gate without requiring drivers to get out of 

the vehicle to use the keypad. This design 

can also be used to mount a Knox Box for 

fire safety. 
Bollards can also be filled with concrete and 

used as barriers to protect keypads, walls, 

or gates.

Figure 9a  and 9b

Summary of Contents for VP keypad controls entry









































Reviews:

No comments

Brands by name

Popular brands

Load more brands