PT AMC131 Hardware Manual Download Page 75

Page: 75 / 108

Firmware Upgrade Process

targetcap

Get the target upgrade capabilities. This command can be used to find out the upgrade
capabilities of an MMC.

ipmitool hpm targetcap

Example:

ipmitool -I lan -H 192.168.0.2 -A none -T 0x82 -B 0 -t 0x74 -b 7 hpm

targetcap

PICMG HPM.1 Upgrade Agent 1.0:

TARGET UPGRADE CAPABILITIES

-------------------------------

HPM.1 version............0

Component 0 presence....[y]

Component 1 presence....[y]

Component 2 presence....[n]

Component 3 presence....[n]

Component 4 presence....[n]

Component 5 presence....[n]

Component 6 presence....[n]

Component 7 presence....[n]

Upgrade undesirable.....[n]

Aut rollback override...[n]

IPMC degraded...........[n]

Defered

activation......[y]

Service affected........[y]

Manual rollback.........[y]

Automatic rollback......[y]

Self test...............[n]

Upgrade timeout.........[100 sec]

Self test timeout.......[0 sec]

Rollback timeout........[5 sec]

Inaccessibility timeout.[5 sec]

1. “Defered” is misspelled in the

ipmitool

utility.

Summary of Contents for AMC131













































































































Search results

Summary of Contents for AMC131

Reviews:

Related manuals for AMC131

Brands by name

Popular brands

PT AMC131, Hardware Manual

Search results

Summary of Contents for AMC131

Reviews:

Related manuals for AMC131

Brands by name

Popular brands