PT AMC131 Hardware Manual Download Page 100 | Manualshive

Page: 100 / 108

background image

Chapter 8: Specifications

100

AMC131 Absolute Maximum Ratings

The values below are stress ratings only. Do not operate the AMC131 at these maximums. See

“DC Operating Characteristics” on page 100

for operating conditions.

Operating Temperature

The operating temperature range is 0 to 55

°

C. The AMC131 comes from the factory with an

integrated heat sink for cooling the processor. The heat sink requires 700 LFM of airflow for the
1.5 GHz option and 250 LFM (linear feet per minute) for all other options.

Caution:

External airflow must be provided at all times during operation to avoid damaging the CPU
module. PT strongly recommends use of a card rack fan tray to supply the external airflow.

DC Operating Characteristics

shows power consumption of an AMC131 with a dual core MPC8641D processor

operating without AltiVec™ and with 2GB DDR 400 SDRAM installed.

Table 8-1:

Power Consumption with 3.3V VIO

Supply Voltage, Vcc12 (+12V):

10-14V

Supply Voltage, Vcc3 (+3.3V):

3.0-3.6V

Storage Temperature:

-20° to +80° C (-4° to 176° F)

Non-Condensing Relative Humidity:

5 to 90%

Voltage (VDC)

Maximum Power (W)

12V

40 - (1.0 GHz, 1.25 GH z, 1.33 GHz options)
53 - (1.5 GHz option)

3.30 V

0.27

«
...
98
99
100
101
102
...
»

Summary of Contents for AMC131













































































































Reviews:

No comments

Related manuals for AMC131

Brand: Avermedia Pages: 27

Brand: KIDDY Pages: 106

Compact Back Pack 2512

Brand: Baby Trend Pages: 5

Brand: Advantech Pages: 2

Brand: Lionelo Pages: 12

Brand: NéoBulle Pages: 20

SIDE-TO-SIDE INFANT CARRIER 79472

Brand: Fisher-Price Pages: 6

Brand: Fisher-Price Pages: 5

Brand: Fisher-Price Pages: 8

FACING YOU 79249

Brand: Fisher-Price Pages: 8

Brand: Fisher-Price Pages: 12

Brand: Fisher-Price Pages: 20

Brand: Fisher-Price Pages: 20

Brand: Fisher-Price Pages: 28

Brand: Fisher-Price Pages: 40

hop-tye advanced

Brand: Hoppediz Pages: 24

Brand: Steelcraft Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands