PT AMC131 Hardware Manual Download Page 76

Page: 76 / 108

Chapter 5: System Monitoring and Alarms

compprop

Get the specified component properties. This command can be used to find out component-
specific properties.

ipmitool hpm compprop <id> <select>

The

<id>

parameter specifies the component whose properties are read; 0 corresponds to the

firmware component and 1 corresponds to the boot loader component. The

parameter specifies the property that should be acquired. The properties are the following:

General properties

Current firmware version

Description string

Rollback firmware version

Deferred firmware version

Example:

ipmitool -I lan -H 192.168.0.2 -A none -T 0x82 -B 0 -t 0x74 -b 7 hpm

compprop 0 0

PICMG HPM.1 Upgrade Agent 1.0:

GENERAL PROPERTIES

-------------------------------

Payload cold reset req....[y]

Def. activation supported.[y]

Comparison supported......[n]

Preparation supported.....[y]

Rollback supported........[y]

Summary of Contents for AMC131













































































































Search results

Summary of Contents for AMC131

Reviews:

Related manuals for AMC131

Brands by name

Popular brands

PT AMC131, Hardware Manual

Search results

Summary of Contents for AMC131

Reviews:

Related manuals for AMC131

Brands by name

Popular brands