PT AMC131 Hardware Manual Download Page 65

Page: 65 / 108

Serial Interface Subsystem

Serial Line Properties Commands

The SIPL provides commands to get/set the properties of the MMC serial interfaces (the serial
debug interface and the payload interface):

•

“Get Serial Interface Properties Command,” on page 65

•

“Set Serial Interface Properties Command,” on page 65

Get Serial Interface Properties Command

The

Get Serial Interface Properties

command is used to get the properties of a particular

serial interface. This command has the following synopsis:

[B8 xx 01 0A 40 00

<interface ID>

]

The

parameter can have one of the values shown in

Table 5-7, “The

<interface ID> Parameter Values,”

below.

The MMC responds to the

Get Serial Interface Properties

command with the following reply:

[BC xx 01 00 0A 40 00

<interface properties>

]

The

parameter has the bit fields shown in

Table 5-8, “The

<interface properties> Parameter Bit Fields,”

below.

Set Serial Interface Properties Command

The

Set Serial Interface Properties

command is used to change the properties of a given

interface:

[B8 xx 02 0A 40 00

<interface ID> <interface properties>

]

Table 5-7:

The

Parameter Values

Interface ID

Description

Serial debug interface

Payload interface

Table 5-8:

The

Parameter Bit Fields

Bits

Name

Description

0-3

Baud Rate ID

The baud rate ID defines the interface baud rate as
follows:
0 – 9600 bps
1 – 19200 bps
2 – 38400 bps
3 – 57600 bps
4 – 115200 bps

4-6

Reserved

7 (MSB)

Echo On

If this bit is set, the MMC enables echo for the given
serial interface.

Summary of Contents for AMC131













































































































Search results

Summary of Contents for AMC131

Reviews:

Related manuals for AMC131

Brands by name

Popular brands

PT AMC131, Hardware Manual

Search results

Summary of Contents for AMC131

Reviews:

Related manuals for AMC131

Brands by name

Popular brands