PRÜFTECHNIK EDDYSENSOR Operating Manual Download Page 31

Page: 31 / 53

EDDYSENSOR Operating Manual

Encoder socket
pin assignment

Pin assignment

–––

+5 Volt with 5V ON

(ext. voltage with 5V OFF), I

max

= 200 mA

Only for PRÜFTECHNIK standard encoder

Clock

–––

GND with switch GND ON

Ext. GND with switch GND OFF

Encoder socket

Switch S1 showing the
settings for a standard

encoder

Switch S1 showing the
settings for a non-
standard encoder

The encoder switch S1 on the back module

PCB (see diagram) must be set when using an

encoder. For the PRÜFTECHNIK standard

encoder 2, 3 and 4 must be set to ON (1 is not

used).

For non-standard encoders 2 must be set to

ON, 3 and 4 must be set to OFF (1 is not used).

If no encoder is used then all must be set to

OFF (to the right).

Encoder switch
up to modification status d

(the status is shown on the
connector block of the PCB)

Encoder switch
from modification status e
onwards

(the status is shown on the con-
nector block of the PCB)

Switch S1 showing the
settings for a standard
encoder

Switch S1 showing the
settings for a non-

standard encoder

The encoder switch S1 on the back module

PCB (see diagram) must be set when using an

encoder. For the PRÜFTECHNIK standard

encoder 1 must be set to OFF, 2 and 3 must be

set to ON.

For non-standard encoders, 1, 2 and 3 must

be set to OFF.

If no encoder is used then 1 must be set to ON,

2 and 3 must be set to OFF (to the right).

Switch S1 showing the

settings for no encoder

Summary of Contents for EDDYSENSOR






















































Search results

Summary of Contents for EDDYSENSOR

Reviews:

Related manuals for EDDYSENSOR

Brands by name

Popular brands

PRÜFTECHNIK EDDYSENSOR, Operating Manual

Search results

Summary of Contents for EDDYSENSOR

Reviews:

Related manuals for EDDYSENSOR

Brands by name

Popular brands