Proxomed Compass 530 Page 42 User Manual Download | Manualshive

Page: 42 / 63

background image

42

an upright position. However, you can also adjust the height accordingly with the help of the
rotation/locking bolt. To do this, turn the knob counterclockwise to disengage the pivot/locking pin and
pull the knob to adjust the height of the entire unit. Then snap the knob back into place and fix it by
turning it to the right.

With the adjustment lever (yellow) on the right side of the seat, the starting position can be adjusted in
10° steps. Select the direction of rotation to the right or left. The Range of Motion Limiter (optional) for
the end position is located above the weight block and is adjusted by loosening the fastening screw.

«
...
40
41
42
43
44
...
»

Summary of Contents for Compass 530
































































Reviews:

No comments

Related manuals for Compass 530

Brand: ABB Pages: 86

Brand: iGuzzini Pages: 20

Brand: Raymarine Pages: 24

Brand: Hansen Pages: 72

Brand: AAT Pages: 16

Brand: AAT Pages: 40

Platinum Series

Brand: Dairy Tech Pages: 38

Brand: H&S Pages: 34

Brand: QAL Medical Pages: 42

Brand: Tascam Pages: 80

Brand: Tascam Pages: 2

Brand: Walker Pages: 24

MET ONE 3400 Series

Brand: Hach Pages: 48

Brand: tayco Pages: 111

Brand: Pari Pages: 12

Brand: laerdal Pages: 2

Brand: laerdal Pages: 104

Brand: laerdal Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands