P. 6
Installation
Guide
CT-3400 TW
Wire
Description
1
BLUE
(–) Zone 3
or AUX 3 output
500 mA negative output. This can be used to control trunk release (1-sec.
pulse) or to operate as a constant output as long as the
TRUNK
button is held
pressed (for Sunroof or Window close).
2
BROWN
(–) Lock
Programmable 500 mA 1/10-sec., 7/10-sec. or 4-sec. negative output.
3
GREEN
(–) Unlock
Programmable 500mA 1/10-sec., 7/10-sec., 4-sec. or 1/4-sec. double-pulse
negative output.
4
WHITE / BROWN
(–) Arm
Max 500 mA ground signal when the doors are locked by remote control.
This wire will go to ground 1/4 sec. before the
LOCK
pulse, and go
OFF
1/8 sec
after it.
Note:
The system will also give a rearm pulse on this wire after
remote-start shutdown.
5
WHITE / GREEN
(–) Disarm
Max 500 mA 1-sec. ground pulse when the Doors are unlocked by remote
control. Connect to the OEM Disarm wire of the vehicle.
Note:
The system
will also give a disarm pulse on this wire before remote starts.
6
BLUE / WHITE
(–) AUX 1 output
This output will provide a 1-sec. negative output (500 mA) when the
UNLOCK
button is pressed a second time on the transmitter (priority door access) or
otherwise when the
LOCK
button is pressed (horn confirmation).
7
WHITE / ORANGE
(–) Starter Kill
(armed output)
The unit is equipped with a selectable
passive-
or
active-arming Starter Kill
circuit that will immobilize the vehicle when the system is armed. This wire will
provide a constant 500-mA negative output when the system is
armed
(locked
by remote) or if remote started. This wire should be connected to a Single Pole
Double-Throw Relay (This wire will connect to Pin 85, on the Relay, and Pin 86
will be connected to the Ignition wire).
A second benefit of the Starter Kill is the Anti-Grind feature. When the vehicle
has been remote started the Anti-Grind prevents the starter motor from re-
engaging when the ignition key is inserted in the
Ignition switch
and
accidentally turned to the
CRANK
position (The Starter Kill output becomes
active during remote starts).
8
ORANGE
(–) AUX 2 output
Negative 500mA output. Can be programmed for one of the following four
options:
(1)
Constant while the
LOCK
and
UNLOCK
buttons are p 1 sec. after
release of buttons.
(2)
LOCK
+
UNLOCK
toggles
ON/OFF
. (Max. 30 sec.)
(3)
LOCK
+
UNLOCK
toggles
ON/OFF
.
(Max. 60 sec.)
(4)
Priority door access.
9
PURPLE
(–) External
Trigger input
This input will start the vehicle when it receives a 1-second ground pulse
from an external pager system or timer module. It will also shut the vehicle
down upon a 1-sec. pulse when running under remote control.
Option 1 –
(-) input Trunk pin
:
When the external trigger wire is programmed as
a Zone 3 sense wire; pressing
TRUNK
will send a 1-second disarm pulse. If Zone
3 is detected (ground), a rearm pulse will be sent 5 seconds after Zone 3
closes. If Zone 3 is unchanged (no ground), a rearm pulse will be sent
4 seconds after the button is pressed (disarm is sent only if the system was
previously locked and armed).
If secure lock is enabled, a lock pulse and a
rearm pulse will be sent.
Option 2 ((-) Input Engine
START/STOP
):
When the external trigger wire is
programmed to trigger the starter a ground pulse on this line will start or stop the
engine.
Option 3 ((-) Input Key Sense):
When the external trigger wire is programmed
