PRONAR ZEFIR 85 Servicing Instruction Download Page 75

Page: 75 / 88

PRONAR

F. TECHNICAL MAINTENANCE OF THE

TRACTOR

PRONAR

agent. Install filtering elements and pour fresh oil into oil sump. Oil level ought to range to the line marked
inside oil sump

. The oil level must not exceed the marking inside the oil sump.

ATTENTION ! If the tractor operates under conditions of heavy dustiness, you must check the air
filter after each 20 mth.

Having the air filter cleaned you must check tightness of its connections.

For this purpose, while the engine is running (at medium speed, ie. approx. 1000 rpm), you must cover

the filter inlet

up. If all connections are tight, the engine will stop. If it does not stop, you must tighten all

fixing elements of the filter, so to obtain aforementioned effect at the second attempt.

OPERATION No. 21.

Cleaning air filter in the compressor

Unscrew and blow through the air filter

in the air compressor with

use of compressed air.

OPERATION No. 22.

Tighteninh the engine head

Tightness of screws fixing engine head must be checked
while the engine is warm, respectively. First you need to
screw the bolts tight by applying force of 80Nm, and then
of 181 Nm.

After having the engine head screwed tight, you must check and adjust valve clearance
of the engine.

Summary of Contents for ZEFIR 85

























































































Search results

Summary of Contents for ZEFIR 85

Reviews:

Related manuals for ZEFIR 85

Brands by name

Popular brands

PRONAR ZEFIR 85, Servicing Instruction

Search results

Summary of Contents for ZEFIR 85

Reviews:

Related manuals for ZEFIR 85

Brands by name

Popular brands