PRONAR ZEFIR 85 Servicing Instruction Download Page 77

Page: 77 / 88

PRONAR

F. TECHNICAL MAINTENANCE OF THE

TRACTOR

PRONAR

TECHNICAL REVIEW (P-3) AFTER 400 MTH OF OPERATION

Take all actions of aforementioned technical review plus:

OPERATION No. 24.

Oil level in the hydraulic system and in gear-box and rear axle

ATTENTION ! Before setting about checking oil level in the hydraulic system and in gear-box and

rear axle, you must position the tractor on level ground, stop the engine and pull the
parking brake.

Oil level in the hydraulic system and gear-box and rear axle in tractors

ZEFIR

must be checked with

use of dip rod

, placed in the filler plug on the rear axle body in the rear of the tracotr.

Oil  level  ought  to  range  between  bottom  and  upper
line on the dip rod located in the filler plug.
       In  case  of  insufficient  oil  content,  you  must  refill
the oil through filler opening

up to required level.

ATTENTION! When working with machines of high capacity hydraulic systems, oil level in the tank

of hydraulic system must range to the upper line on the dip rod.

ATTENTION! It is forbiden to start the tractor if oil level in the tank ranges below the bottom line on

the dip rod.

OPERATION No. 25.

Oil level in the body and wheel reduction gear of the front driving axle

Verification of oil level in the wheel reduction gear of the front axle must be performed after arranging

filler-control opening

along horizontal axis of the wheel section. Oil level ought to range to bottom edge of

the filler-control opening

. If need be, refill the oil through filler-control opening

Oil level in the main gear of the front driving axle ought to range to bottom edge of the filler-control

opening

. If need be, refill the oil through filler-control opening

Summary of Contents for ZEFIR 85

























































































Search results

Summary of Contents for ZEFIR 85

Reviews:

Related manuals for ZEFIR 85

Brands by name

Popular brands

PRONAR ZEFIR 85, Servicing Instruction

Search results

Summary of Contents for ZEFIR 85

Reviews:

Related manuals for ZEFIR 85

Brands by name

Popular brands