Promise Technology SuperSwap 4600 User Manual Download | Manualshive

Page: 28 / 34

background image

SsuperSwap 4100 User Manual

22

Fan Replacement

To replace a fan on the SuperSwap 4600, do the following:

1.

Power down the PC.

2.

Remove the SuperSwap enclosure from the PC chassis.

3.

Remove the two mounting screws on the fan.

4.

Pull the fan from the two mounting pins and the wire away from the bracket.

Do not bend the bracket.

5.

Unplug the power connector.

6.

Plug the power connector of the new fan.

7.

Lay the wire through the bracket and place the fan onto the two mounting
pins.

8.

Install the two mounting screws.

9.

Reinstall the SuperSwap enclosure into the PC chassis.

10. Power up the PC and check fan function.

Mounting Screw

Wire Bracket

Power Connector

Mounting Pin

Fan

«
...
26
27
28
29
30
...
»

Summary of Contents for SuperSwap 4600



































Reviews:

No comments

Related manuals for SuperSwap 4600

Brand: Nanoxia Pages: 11

WHAD HE 3 101 66

Brand: LEGRAND Pages: 100

Brand: ZALMAN Pages: 34

Brand: Evolveo Pages: 10

Brand: MediaSonic Pages: 5

Brand: NetShelter Pages: 44

Brand: Compaq Pages: 32

Brand: multicomp pro Pages: 2

Brand: Conteg Pages: 40

Brand: RICHER Pages: 6

Brand: Vantec Pages: 23

Brand: Altronix Pages: 4

PCRWESKD06U55BK

Brand: Nexxt Pages: 4

Brand: Carousel USA Pages: 15

Brand: Fantec Pages: 2

Brand: Fantec Pages: 2

Brand: Tote Vision Pages: 1

Brand: Salvus Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands