manualshive.com logo in svg

ProMinent DULCOMETER D1C Type D, Operating Instructions Manual, Page: 25 / 28

Share
Download
ProMinent DULCOMETER D1C Type D Operating Instructions Manual Download Page 25

25

Complete Operating Menu / Description

Feed forward control

Standard signal output 1

feed forward ctrl.

Hz / mA

10 Hz

D1C2-cond.-035-GB

feed forward ctrl.
setting  ?

max. additive

feed forward ctrl.

regulated value

10.00 Hz

effect:

feed forward ctrl.

additive

100 %

feed forward ctrl.:
rated value:

D1C2-cond.-027-GB

0…20 mA

  0 mA =

20 mA =

   0%

  0 mA =

20 mA =

100%

➞➞

positive cond
negative cond

Access to all setting menus can be blocked with an access code !

Control with standard signal

mA output 1  PS1

setting  ?

only with standard signal output

mA output 1

control

regulated value:

mA output 1

regulated value

measured value

mA output 1
measured value

mA output 1

100.0 

°

C

  0 mA =

20 mA =

correction value

0.0 

°

C

0,0 mS/cm

200.0 mS/cm

Possible values

Initial value

Increment

Lower value

Upper value

Remarks

Feed forward control

as per

none

Signal processing:

(flow)

identity code at

10 Hz

Signal < 0,2 mA = No flow

standard signal

500 Hz

Signal < 4,2  mA = No flow

0...20 mA
4...20 mA

Feed forward control

20 mA

0.01 mA

0/4 mA

20 mA

Depending on signal type.

rated value

10 Hz

0.01 Hz

0.1 Hz

10 Hz

Maximum limitation of

500 Hz

1 Hz

5 Hz

500 Hz

range used.

Feed forward control

multiplicative

multiplicative

Feed forward effect

additive

Max. additive regulated

100 %

1 %

-500 %

+500 %

Only with additive

value

regulated value.

BA_DM_138_09_06_GB.p65

21.09.2006, 11:22 Uhr

25

Summary of Contents for DULCOMETER D1C Type D





























Reviews:

No comments