ProMinent DULCOMETER D1C Type D Operating Instructions Manual Download Page 17 | Manualshive

Page: 17 / 28

ProMinent DULCOMETER D1C Type D Operating Instructions Manual Download Page 17

17

Complete Operating Menu / Description

Installation factor setting

Enter the installation factor of the installed sensor here (arrow keys!). Determine the installation factor using
the data from the sensor documentation and the installation geometry.

D1C2-cond.-041-GB

install. factor

setting ?

install. factor

1.00

100

µ

S/cm

Possible values

Initial value

Increment

Lower value

Upper value

Remarks

Installation factor

1.00

0.01

0.01

9.99

Type of sensor setting

When changing the sensor, press Enter to load the actuation parameters permanently stored in
DULCOMETER

®

D1C for this sensor type. Metering and control stop and the measured value-specific error

messages are deleted.

D1C2-cond.-044-GB

type of sensor

setting ?

type of sensor :

ICT 1

sensor data

are changed!

Possible values

Initial value

Increment

Lower value

Upper value

Remarks

Type of sensor

ICT 1

ICT 1

The default

ICT 1-IMA

actuation parameters

ICT 2 / CLS50

are loaded

ICT 3 / CLS52

IMPORTANT

• The limit values, the setpoints and the standard signal outputs are set to the default

values.

• Check the settings in all menus!

BA_DM_138_09_06_GB.p65

21.09.2006, 11:22 Uhr

17

«
...
15
16
17
18
19
...
»

Summary of Contents for DULCOMETER D1C Type D





























Reviews:

No comments