manualshive.com logo in svg

ProMinent DULCOMETER D1C Type D, Operating Instructions Manual, Page: 23 / 28

Share
Download
ProMinent DULCOMETER D1C Type D Operating Instructions Manual Download Page 23

23

D1C2-cond.-025-GB

Access to all setting menus can be blocked with an access code !

servomotor
setting  ?

dosing
control range:
0 % to

operating range

100 %

only with servomotor

servomotor

current position:

servomotor
open

servomotor

please wait  !

open

servomotor

please  wait  !

closed

servomotor

Value take over ?

opened  !

servomotor

value take over ?

closed  !

servomotor
close  ?

servomotor

current position:

OK

= automatic timing

cond

setting

➞

Servomotor

The 

operating range

 is given by the overall resistance range of the feedback potentiometer. Defining the

control range places a maximum limit on the 

control range

 used.

IMPORTANT

• The servomotor must be actuated with the same care as for the calibration of a measuring

sensor.

• To ensure correct function, the control duration of the servomotor must be at least

25 seconds for 0...100 % of the control range.

Complete Operating Menu / Description

Possible values

Initial value

Increment

Lower value

Upper value

Remarks

Servomotor

Setting

Setting

ok

off

Control direction

Cond.

Cond.
Cond.

Control range

100 %

1 %

10 %

100 %

in % of

operating range

NOTE

• When the wide bar is as far right as it will go, the servomotor is fully open.

• The permanent display shows to what degree the motor has opened in % (the greater the

percentage, the farther open the servomotor).

BA_DM_138_09_06_GB.p65

21.09.2006, 11:22 Uhr

23

Summary of Contents for DULCOMETER D1C Type D





























Reviews:

No comments