Particular safety instructions:
Always observe the relevant instructions applicable for the work to be carried out by the user (regulations for
the prevention of accidents.)
The anchor point should be above the user and have a minimum load bearing capacity conforming to EN 795
(min. 10 kN).
Front mounted fall arrest attachment element A/2: the following applies for connection of the 2 belt loops (see
page 3) (provided that the included karabiner is not used): karabiner EN 362 of type B may be loaded only in the
main axis (EN 362:2005). If this cannot be ensured by the user, karabiners EN 362 of type M (EN 362:2005) must be
used. If in doubt, consult the manufacturer prior to use of the full body harness!
The equipment should personally belong to the user.
The equipment should be used only by trained and qualified persons.
Strictly observe the cleaning instructions.
The full body harness is approved for securing only one person.
It is forbidden to make any modification to the personal protective equipment.
Modifications as well as repair work must be carried out only by the manufacturer!
Use of the Preising full body harnesses: -20
°
C up to +60
°
C.
Use only dry full body harnesses when starting work.
Suitable for persons having a weight of max. 150 kg.
The instructions for use for all personal protective equipment used in combination with the full body harness
must be absolutely observed.
Prior to the use of the complete personal protective equipment, the user must find out about possible risks
which may occur at the place of use and then use the personal protective equipment in accordance with the
requirements. Also, a rescue concept should be available for the concrete application case.
Training regarding the use of full body harnesses in accordance with the requirements is offered by the
manufacturer.
Storage:
Preferably in dry, well-ventilated rooms; keep away from sources of heat!
Transport:
A suitable container protecting the personal protective equipment from contamination and damage during
transport, should be used, e.g. equipment bag No. 5099L, rucksack No. 5099/S4.
Cleaning:
Clean the full body harness with lukewarm water by adding standard detergents.
Desinfection:
Please contact directly the manufacturer if desinfection of the personal protective equipment should be
required.
Drying:
Hang up in warm ventilated rooms, however not near to a fire or any other source of heat >60
°
C.
Checks and regular inspections:
Prior to each use, visual inspection of the full body harness must be carried out
regarding impeccable condition in order to ensure the user’s safety which depends e.g. upon the effectiveness and
durability of the full body harness.
Particular attention should be made regarding the following: cuts, wear, damage due to heat, chemicals and similar,
undamaged seams and fittings (no corrosion, no mechanical deformation or cuts as well as inspection regarding
impeccable function). Check the impeccable function of karabiners as per EN 362 which are included in the scope of
supply of the full body harness, i.e. snap safety catch closes without problem and clicks in completely, the locking screw
element can be operated smoothly and correctly, self-locking twist fasteners and Trilock fasteners latch in completely as
envisaged and lock impeccably.
All fasteners are free from any contamination which might impair their function.
Damaged full body harnesses must not be used, also not when there are doubts regarding their safe condition
Î
pass on
to a competent person or to the manufacturer for inspection (address see page 1 of these instructions for use)! Only use
original parts made by Preising!
A full body harness which has been used for an arrest fall, must be immediately put out of service and sent to the
manufacturer for inspection.
It may be used again only following written approval by the manufacturer (address see page 1 of these instructions for use)!
The full body harness must be inspected by a competent person as necessary, however at least every 12 months in
compliance with EN 365. An inspection card (attached to these instructions for use) is enclosed in the scope of supply of
each full body harness. A respective inspection plan to be followed by the qualified person, can be obtained from the
manufacturer upon request (address see page 1). Furthermore, it must be verified that the full body harness is provided
with a readable identification.
Training to become a qualified person for carrying out the regular inspection of full body harnesses, is offered by the
manufacturer.
(Basis training for the period inspection).
