Precision Digital Corporation PD765-6X0-00 Instruction Manual Download Page 66

Page: 66 / 71

Trident Model PD765 Universal Input Meter Instruction Manual

Reset Meter to Factory Defaults

When the parameters have been changed in a way that is difficult to de-
termine what’s happening, it might be better to start the setup process
from the factory defaults.

Instructions to load factory defaults:

1. Enter

the

Advanced

Features Menu

. See

Advanced Features

Menu

, page 50.

2. Press

arrow to go to

Diagnostics

3. Press and hold

Right

arrow/Reset for five seconds, press

Enter/Ack

when display flashes

reset

Note: If

Enter/Ack

is not pressed within three seconds, display re-

turns to

Diagnostics

menu.

4. The meter goes through an initialization sequence (same as on

power-up), and loads the factory default settings.

rset

diag

Press Simultaneously

Meter Re-

Initializes

Press and Hold
for 5 Sec

Flashing
Display

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for PD765-6X0-00








































































Search results

Summary of Contents for PD765-6X0-00

Reviews:

Related manuals for PD765-6X0-00

Brands by name

Popular brands

Precision Digital Corporation PD765-6X0-00, Instruction Manual

Search results

Summary of Contents for PD765-6X0-00

Reviews:

Related manuals for PD765-6X0-00

Brands by name

Popular brands