Precision Digital Corporation PD765-6X0-00 Instruction Manual Download Page 11

Page: 11 / 71

Trident Model PD765 Universal Input Meter Instruction Manual

Isolated 4-20 mA Transmitter Output

OUTPUT RANGE

1.00 to 23.00 mA typical

CALIBRATION

Factory calibrated for 4-20 mA

SCALING RANGE

0.00 to 23.99 mA for any display range,
see output range above

ACCURACY

± 0.1% FS ± 0.004 mA

TEMPERATURE
DRIFT

0.4 uA/

C from -40 to 65

C ambient

Note: Analog output drift is separate from input drift.

ISOLATED
TRANSMITTER
POWER SUPPLY

One or two transmitter power supplies (Optional)
P1: 24 VDC

10% @ 200 mA max. (-1 option)

P1 & P2: 24 VDC

10% @ 200 mA & 40 mA max. (-2 option)

EXTERNAL LOOP
POWER SUPPLY

35 VDC maximum

OUTPUT LOOP
RESISTANCE

Power supply

Minimum

Maximum

24 VDC

700

35 VDC (external)

100

1200

Serial Communications

METER
ADDRESS

PDC protocol: 0 - 99
Modbus protocol: 1 - 247

BAUD RATE

300 – 19,200 bps

TRANSMIT
TIME DELAY

Programmable between 0 and 199 ms

DATA

8 bit (1 start bit, 1 stop bit)

PARITY

None (1 or 2 stop bits), even, or odd
(Modbus only; PDC protocol does not use parity)

BYTE-TO-BYTE
TIMEOUT

0.01 – 2.54 sec (Modbus only)

TURN AROUND
DELAY

Less than 2 ms (fixed)

Refer to PDC and Modbus Serial Communication Protocol manuals for
details. These can be downloaded from: www.predig.com.

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for PD765-6X0-00








































































Search results

Summary of Contents for PD765-6X0-00

Reviews:

Related manuals for PD765-6X0-00

Brands by name

Popular brands

Precision Digital Corporation PD765-6X0-00, Instruction Manual

Search results

Summary of Contents for PD765-6X0-00

Reviews:

Related manuals for PD765-6X0-00

Brands by name

Popular brands