Precision Digital Corporation PD765-6X0-00 Instruction Manual Download Page 24

Page: 24 / 71

Trident Model PD765 Universal Input Meter Instruction Manual

Front Panel Buttons and Status LED Indicators

Button
Symbol

Description

LED

Status

Menu

1 Alarm

Right arrow/Reset

2 Alarm

Up arrow/Max

Set point indicator

Enter/Ack

Reset point indicator

•

Press

the

Menu

button to enter or exit the Programming Mode at

any time.

•

Press

the

Right

arrow button to move to the next digit during digit

programming.

•

Press

the

arrow button to scroll through the menus, decimal

point, or to increment the value of a digit.

•

Press

the

Enter/Ack

button to access a menu or to accept a setting.

•

Press

the

Right

arrow and

Menu

button simultaneously or hold the

Menu

button for approximately 3 seconds to access the

Advanced

Features Menu

of the meter.

For

Interactive Virtual

Meter Demo

visit

tvm.predig.com

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for PD765-6X0-00








































































Search results

Summary of Contents for PD765-6X0-00

Reviews:

Related manuals for PD765-6X0-00

Brands by name

Popular brands

Precision Digital Corporation PD765-6X0-00, Instruction Manual

Search results

Summary of Contents for PD765-6X0-00

Reviews:

Related manuals for PD765-6X0-00

Brands by name

Popular brands